机器保养
1、 定期检查夹口处的螺丝，如有松动应及时拧紧;
2、 与衬板接触的钢板滑动面及衬板的燕尾槽面应保持清洁，并应定期涂上一层薄薄的二硫化钼油脂;
3、定期检查链轮的转动情况。 如发现松动，请重新加紧链轮。
定期检查主机及油源是否有漏油现象。 如有漏油，应及时更换密封圈或组合垫。
根据机器的使用情况和油的使用寿命，定期更换滤油器和滤芯，更换液压油。
长时间不做试验时，注意关闭主机电源。 如果机器处于待机状态，应将转换开关打到“负载”档，因为如果转换开关打到“快回”档，电磁阀已通电，会影响设备的使用寿命。
1. 定期检查控制器后面板连接线是否接触良好。 若松动，应及时拧紧;
二、测试完毕后，如果有很长一段时间机器不使用，关掉控制器和电脑;
3. 控制器上的接口相互对应。 接口错误可能会对设备造成损坏。
四、拔插控制器上的接口必须关闭控制器电源。
5、根据机器的使用和石油的生活,定期更换吸油过滤器滤芯,更换液压油,定期检查主机和油源是否有漏油,如石油泄漏,应及时更换密封圈或组合垫。
英斯特力仪器是一家集研发、生产及销售于一体的影像测量仪，拉力试验机,硬度计,探伤仪,粗糙度仪,测厚仪,金相设备厂家,致力于为客户提供更好的检测仪器。
Machine maintenance
1. Check the screws at the clamping mouth regularly, and tighten them in time if they are loose;
2. The sliding surface of the steel plate in contact with the lining plate and dovetail groove surface of the lining plate should be kept clean, and a thin layer of molybdenum disulfide grease should be regularly coated;
3. Check the rotation of the sprocket regularly. Tighten the sprocket again if it is loose.
Oil source maintenance
Check the main engine and oil source regularly for oil leakage. If there is oil leakage, the sealing ring or combined pad should be replaced in time.
According to the use of the machine and the service life of the oil, regularly replace the oil filter and filter element, replace the hydraulic oil.
When not doing the test for a long time, pay attention to turn off the host power. If the machine is in standby state, the transfer switch should be switched to "load", because if the transfer switch is switched to "fast back", the solenoid valve is energized, will affect the service life of the equipment.
Control system maintenance
1. Periodically check whether the cables on the rear panel of the controller are in good contact. If loose, should be tightened in time;
2、 after the test, if the machine is not used for a long time, turn off the controller and computer;
3. Interfaces on the controllers correspond to each other. An incorrect interface may damage the device.
4, plug and unplug the interface on the controller must turn off the controller power.
5, according to the use of the machine and the life of oil, regular replacement of oil absorption filter element, replacement of hydraulic oil, regular inspection of the host and oil source whether there is oil leakage, such as oil leakage, should be replaced in time seal ring or combined pad.
客服1 